Tiêu đề 38 Commercial Grill.pdf ✅

Test Method Conformity Assurance Dammam – Electrical Lab Product Commercial Grill Issue date 01/04/2024 Test method # TMD01038 Revision 01 Reference standered SASO GSO IEC 60335-2-29 and SASO GSO IEC 60335-1 Revision date 01/04/2024 Result /النتيجة Name of the test/ االختبار اسم البند رقمClause No. Checking Frequency MOCI_D_267A Checking country of origin MOCI_D_267B Checking for Rated Voltage MOCI_D_267B 7 instructions and Marking الوسم و االرشادات to access against Protectionالحماية من الوصول الى االجزاء المكهربة live parts 8 التيار و القدرةPower input and current 10 Heating – rise Temperature االرتفاع في الحرارة 11 and current Leakageتيار التسريب و المتانة الكهربائية electric strength 13 19 operation Abnormal التشغيل غير الطبيعي 20 hazard mechanical and Stabilityاالتزان و االخطار الميكانيكية (2203SASO(4.3 Plug المقننات القابس : الشكل و المقاسات و
Test Method Conformity Assurance Dammam – Electrical Lab Product Commercial Grill Issue date 01/04/2024 Test method # TMD01038 Revision 01 Reference standered SASO GSO IEC 60335-2-29 and SASO GSO IEC 60335-1 Revision date 01/04/2024 7 Marking 7.1 Appliances shall be marked with the: – rated voltage or rated voltage range in volts – symbol for nature of supply, unless the rated frequency is marked; – rated power input in watts or rated current in amperes; – name, trade mark or identification mark of the manufacturer or responsible vendor – model or type reference symbol 5172 of IEC 60417, for class II appliances only IP number according to degree of protection against ingress of water, other than IPX0 Addition Appliances incorporating induction heating sources shall in addition be marked with : - operating frequency or operating frequency range in kilohertz (kHz); - the total power input of all the induction heating units that can operate simultaneously, in watts or kilowatts, unless this is indicated in the instruction sheet; - the total power input of all the non-induction heating units that can operate simultaneously in watts or kilowatts unless this is indicated in the instruction sheet. The enclosure of electrically-operated water valves incorporated in external hose-sets for connection of an appliance to the water mains shall be marked with symbol IEC 60417-5036 (DB:2002-10) if their working voltage exceeds extra-low voltage. Any cover giving access to live parts at a working voltage exceeding 250 V shall be marked by the following: WARNING – DANGEROUS VOLTAGE or by the symbol for dangerous voltage (see 7.6).
Test Method Conformity Assurance Dammam – Electrical Lab Product Commercial Grill Issue date 01/04/2024 Test method # TMD01038 Revision 01 Reference standered SASO GSO IEC 60335-2-29 and SASO GSO IEC 60335-1 Revision date 01/04/2024 Covers giving access to induction coils shall be marked by the following: CAUTION – MAGNETIC FIELD or by the symbol for non-ionizing electromagnetic radiation (see 7.6). 7.2 Stationary appliances for multiple supply shall be marked with the substance of the following: Warning: Before obtaining access to terminals, all supply circuits must be disconnected. This warning shall be placed in the vicinity of the terminal cover. 7.3 Appliances having a range of rated values and which can be operated without adjustment through out the range shall be marked with the lower and upper limits of the range separated by a hyphen. Appliances having different rated values and which have to be adjusted for use at a particular value by the user or installer shall be marked with the different values separated by an oblique stroke. 7.4 If the appliance can be adjusted for different rated voltages, the voltage to which the appliance is adjusted shall be clearly discernible. 7.5 For appliances marked with more than one rated voltage or with one or more rated voltage ranges, the rated power input or rated current for each of these voltages or ranges shall be marked 7.6 Correct use of symbols 7.7 Appliances to be connected to more than two supply conductors and appliances for multiple supply shall have a connection diagram fixed to them, unless the correct mode of connection is obvious. 7.8 Terminals used for connection to the supply mains shall be indicated as follows: Terminals intended exclusively for the neutral conductor shall be indicated by letter N Protective earthing terminals shall be indicated by the symbol 5019 of IEC 60417.
Test Method Conformity Assurance Dammam – Electrical Lab Product Commercial Grill Issue date 01/04/2024 Test method # TMD01038 Revision 01 Reference standered SASO GSO IEC 60335-2-29 and SASO GSO IEC 60335-1 Revision date 01/04/2024 7.9 Unless it is obviously unnecessary, switches which may give rise to a hazard when operated shall be marked or placed so as to indicate clearly which part of the appliance they control. 7.10 Indication of the different positions of switches on stationary appliances and the different positions of controls on all appliances shall be indicated by figures, letters or other visual means If figures are used for indicating the different positions, the off position shall be indicated by the figure 0 and the position for a higher value, such as output, input, speed or cooling effect, shall be indicated by a higher figure. The figure 0 shall not be used for any other indication unless it is positioned and associated with other numbers so that it does not give rise to confusion with the indication of the off position. The off position of touch controls for hobs shall be marked by the figure O and the on position by the figure I. If there is no touch control for the hob, this requirement applies to the touch controls for each hob element. 7.11 Controls intended to be adjusted during installation or in normal use shall be provided with an indication for the direction of adjustment 7.12 Instructions for use shall be provided with the appliance so that the appliance can be used safely If it is necessary to take precautions during user maintenance, appropriate details shall be given. Addition If the appliance incorporates a hob surface of glass-ceramic or similar material that provides the enclosure of live parts, the instructions shall include the substance of the following warning: WARNING: If the surface is cracked, immediately disconnect the appliance or appropriate part of the appliance from the supply.