Tiêu đề ETE Framed MCQs Msbteallclear.com .pdf ✅

Set 1: Question No 1 Set 1: Question No 2 Set 1: Question No 3 ___________and __________ architectures improve the performance of the processor. Increasing the clock speed __________the power consumption. In battery operated devices ________ is the important processor selection criteria. Recall/ Remembering Understanding Application a) Pipelining, super-scalar a) Decreases a) Power b) Cost , Size b) Increases b) Memory c) Memory, Size c) Not known c) Size d) Peripherals, operating voltage d) Contract d) Cost Ans: < a > Ans: < b > Ans: < a > Set 2: Question No 1 Set 2: Question No 2 Set 2: Question No 3 Graphic Processing Unit also called as ___________unit. System On Chip (SoC) architecture provides _______peripherals to improve Effective data communication. Suggest processor to handle multimedia applications. Recall/ Remembering Understanding Application a) ALU a) off chip a) Digital Signal Processor b) Register b) side by side b) Floating Point Co-processor c) Visual processing c) near by c) Microprocessor d) Stack pointer d) on chip d) Microcontroller Ans: < c > Ans: < d > Ans: < a > Set 1: Question No 1 Set 1: Question No 2 Set 1: Question No 3 CISC includes _________complex instruction. RISC has__________ performance. The computer architecture aimed at reducing the time of execution of instructions is ________. Recall/ Remembering Understanding Application a) Double a) Lower a) CISC b) Single b) Higher b) RISC c) Multi clock c) Medium c) ISA d) Tripple d) Moderate d) ANNA Ans: < c > Ans: < b > Ans: < b > msbteallclear.com

Set 1: Question No 1 Set 1: Question No 2 Set 1: Question No 3 Arduino Uno board has _____ Analog Input pins. Alternate power source to Arduino board is Arduino is a ___________ hardware and software platform. Recall/ Remembering Understanding Application e) 2 e) USB port e) licensed f) 12 f) JTAG port f) open-source g) 14 g) HDMI port g) Govern software h) 6 h) VGA port h) dedicated Ans: < d > Ans: < a > Ans: < b > Set 2: Question No 1 Set 2: Question No 2 Set 2: Question No 3 Arduino Uno board having _____ Digital I/O pins. Operating voltage of Arduino is Arduino IDE run on _______ platform Recall/ Remembering Understanding Application a) 14 e) 230V e) single b) 12 f) 12V f) double c) 5 g) 9V g) triple d) 6 h) 3.3V h) multiple Ans: < a > Ans: < d > Ans: < d > Set 1: Question No 1 Set 1: Question No 2 Set 1: Question No 3 Program instructions are stored in __________ memory. Function of JTAG port is In Atmega 328p chip P refers to Recall/ Remembering Understanding Application i) non-volatile flash i) Fetch i) production j) volatile j) Debug j) pinmode k) primary storage k) Decode k) pico-power l) RAM l) Execute l) programmable on chip Ans: < a > Ans: < b > Ans: < c > msbteallclear.com
Set 2: Question No 1 Set 2: Question No 2 Set 2: Question No 3 The AVRs have ____ single- byte registers and are classified as 8-bit RISC devices. Function of Data Direction Register is Atmel's AVRs have a ________ Recall/ Remembering Understanding Application e) 8 a) configures the pins as either inputs or outputs level pipeline design. f) 16 b) configures timer level pipeline design. g) 32 c) configures counter k) Four-stage, four- level pipeline design. h) 64 d) configures serial port l) Two-stage, single- level pipeline design. Ans: < c > Ans: < a > Ans: < d > Set 1: Question No 1 Set 1: Question No 2 Set 1: Question No 3 Arduino IDE consists of two functions what are they? Function of boot loader is_____ Select Appropriate command to read Digital Pin number 2. Recall/ Remembering Understanding Application m) build() and loop() i) Installing new firmware m) digitalWrite(pin); n) setup() and build() j) Add two registers n) pinMode(pin,mode) o) setup() and loop() k) Transfer the data into register o) delay (ms); p) build() and jump() l) Shift the data towards right p) digitalRead(2); Ans: < c > Ans: < a > Ans: < d > Set 2: Question No 1 Set 2: Question No 2 Set 2: Question No 3 ______ are used to write blocks of code in Arduino IDE sketch. A program written with the IDE for Arduino is called as? ____ Function is called once when a sketch starts after power up or reset. Recall/ Remembering Understanding Application i) Colon a) IDE source q) loop() j) Semicolon b) Sketch r) while() k) Curly brackets c) Cryptography s) setup() l) Square brackets d) Source code t) pinmode() Ans: < c > Ans: < d > Ans: < c > msbteallclear.com